Triad RF Systems

CubeSat and SmallSat

Closing a Low Earth Orbit link across hundreds of miles is challenging, and the difficulty only multiplies as CubeSats become tasked to provide increasing amounts of bandwidth and data rates across limited-spectrum links. The relatively short mission lengths of CubeSats allow for their radio systems to be continually upgraded and deployed at a much faster rate than traditional large satellite deployments. RF subsystem technology must keep pace. That’s why Triad’s engineering team remains adept at designing for the rigors of the CubeSat environment. In addition to designing in advance for lighter weight and tighter requirements, we perform the requisite analysis to ensure each RF amplifier and radio system we deploy passes all pre-flight requirements.

 

Triad further expanded their product line to provide RF amplifiers and subsystems for CubeSat payloads. These include extremely efficient, ultra small, power amplifiers, BUCs, and complete bi-directional RF sub-systems in UHF, S, and X band. We have recently upgraded our RF labs to support mm-Wave design and test, and are currently designing micro-size, Ka band BUCs and Tx/Rx modules for advanced CubeSats. These assemblies are circuit card form factors that fit up/down conversion, RF filtering, amplification, LNAs and switching in unprecedented package sizes of low size, weight, and power to achieve SWaP objectives.

 

Below we’ve listed products and datasheets relevant to this application type. If you have questions regarding our products or areas of expertise, get in touch today!

Product   Datasheet
TA1109 
S Band 4W Circuit Card Amplifier
S Band 4W Circuit Card Amplifier that has a flight heritage since 2017. It covers the 2000-2500 MHz Band, with a gain of 28dB that can be adjusted for different requirements. It can interface with any SDR that operates in this band and has a compact 2.7 x 1.3” footprint. It can accept a wide input voltage range to accommodate battery-powered cubesat power busses. Read More » downloadPDF
TFTA1005 
L to X-Band 4W Upconverter Amplifier
L to X-Band 4W Upconverter Amplifier used in high data rate systems, and can operate with a wide variety of IFs from L band to S band. It has a flight heritage since 2019 and achieves 4W of output power from 8.0 - 8.5 GHz. It also boasts a wide input voltage and an ultra compact size usable in cubesats down to 1U. Read More » downloadPDF
TA1120
380-470 MHz UHF 4W Circuit Card Amplifier
380-470 MHz UHF 4W Circuit Card Amplifier with flight heritage since 2019. This unit is capable of 4W of output power and supports any modulation from FM to highly modulated QAM signals such as 256QAM. Read More » downloadPDF
TTRM1212 
Full Duplex L-Band Tx/Rx Transceiver Card
Full Duplex L-Band Tx/Rx Transceiver Card with a single 4W amplifier section from 1518-1559 MHz that supports two SDR Tx channels and dual, tightly filtered receive sections (1518-1559 and 1626-1675 MHz) with over 60 dB of cross band isolation. There is a switch bank on board that is controlled via CPLD for high speed, <1uS switching capability. TTL or serial control is available. This product is scheduled for a 2020 CubeSat mission. Request a quote today! downloadPDF
TTRR1086 
80W Dual Channel Bi-Directional UHF Rack Mount Amplifier
180W Dual Channel Bi-Directional UHF Rack Mount Amplifier for CubeSat Ground Stations operating in the 400-450 MHz bands. This rack mount and its predecessors have been deployed worldwide for Ground Station Deployments since 2015, and has been used by several leaders in the CubeSat industry. This supports two SDR radios operating concurrently, and has integral Tx and Rx filtering and Tx power and VSWR measurement. Remote Control and Monitoring is available over Serial and TCP/IP - it also features a Browser Based GUI and SNMP monitoring and control. Request a quote today! downloadPDF
All rights reserved. Copyright ©2019 Triad RF Systems
X
We use cookies to enhance your user experience. By continuing to browse this site, you are giving your consent for cookies to be used. For more information, please refer to our Privacy Policy.